fire retardant logo

Fire Retardants Texas - Fort Worth/Dallas based

Hotline: 800-333-9197 7am-5pm (CST) Ph: 817-740-9197

After Hours: 817-658-9197 / email: fireprod@aol.com

2653 Warfield Street Fort Worth, TX 76106

Dallas, Ft Worth, Austin, Houston, Corpus Christi, Wichita Falls, Abilene, Amarillo, Plano, North Dallas, El Paso, Laredo, Frisco, South Dallas, Lancaster, Dallas County, Tarrant County, Odessa, Waco, Midland, Tyler, Dallas, San Antonio,Lubbock, East Dallas, Grand Prairie, Irving, Dallas / Fort Worth metroplex
Home About Us
thatch safe logo
THATCH SAFE

INTERIOR/EXTERIOR FIRE RETARDANT
COATING or SPRAY FOR ROOF THATCHING, BAMBOO, REED, KOA, TIKI HUT THATCHING

COMPLIES WITH ASTM E84 and ASTM E108

thatch safe logo

TECHNICAL DATA

INTERIOR / EXTERIOR

PRODUCT DESCRIPTION:    Aqueous Based Resin

PRODUCT ANALYSIS
Total Solids
42%   PH
2.8 - 2.9
Weight per gallon
10.5 lbs Flash point
Non-Flammable
Specific gravity
1.33 Color
Water clear at 78°F. - Slight haze at 50°F. or lower
Volatability
Non-Volatile Solvents
Water(Contains no petroleum or derivatives of petroleum)
Anti-Fungus
excellent Resistance Bacterial
Good Resistance
Linear shrinkage
None Moisture Absorption
None
Corrosive
Mildly Toxic
None (when dry)
Insects, rodents,
aspergilli And other types of molds
Excellent resistance Termites
Excellent resistance
Preservative for wood
Good Scrubability
1000 cycles

RECOMMENDED USE: Interior/Exterior

FLAME SAFE THATCH SAFE is a fire retardant coating. It can be used on any type of wood, porous, or non-porous materials, such as:

Thatching Bamboo Koa Cypress

ENVIRONMENTAL REGULATION:

This product complies will U. S. Federal Regulations concerning the use of lead in paint and hydrocarbon emissions.


QUICK REFERENCE FOR APPLYING FIRE POLY FP 75E

MATERIAL APPLICATION
COVERAGE
Thatch, Bamboo, Koa, Cyoress, Roof Thatching, Tiki Hut Thatching

Treat before, during or after construction.

Be sure surface is clean and dry before treating.

Apply with 80 psi or greater sprayer at 8 to 12 inches from surface. Start at the top, hold sprayer at up angle to roof pitch to allow spry under thatching ends.

Apply with brush or roller.

May be necessary to wipe on hardwood surfaces

Treat all surface areas where possible

Do not expose treated area to moisture for 24 hours.

Apply three (3) coats at 500 sq. ft. per gallon with the final coverage rate of 166 sq. ft. per gallon. Allow each coat to dry thoroughly before applying the next coat.

EXTERIOR / INTERIOR

           All surfaces to be treated must be clean and dry. Thatch Safe is water-based, clear liquid that becomes insoluble when dry. Thatch Safe acts as a preservative, and water proofing agent ultra violet inhibibor, mold and mildew protector and repels insects. If over coating is intended, Thatch Safe is an excellent surface primer for use under latex paints or can be use as a finished coat overwater based stains.

DO NOT DILUTE OR MIX FIRE POLY 100 WITH ANY OTHER PRODUCTS.

         It should be noted that unlike some products, materials treated with Thatch Safe require no special cutting tools or special fasteners. Contact parts of any equipment should be stainless steel or plastic to prevent chemical reaction and breakdown. Storage may be done in polyethylene containers.

Thatching with cypress and koa

Thatching with cypress and koa

CAUTION:

          Product must not freeze. It must not be thinned or diluted.


OVERSPRAY:

        The overspray will not harm plants or animals. Spills can be flushed with water. A rag wetted with   bleach and water mix will clean up spotting.


CLEAN UP PROCEDURE:

          Airless Equipment.

1. Run clear water through the system until coating is flushed out. When minor sudsing on surface stops, the system is flushed.

2. Run bleach and water mix (1 part to 4 parts) through system as solvent for cleaning any residue.

            3. Repeat Step 1 if any foaming occurs in Step 2.

            4. Lubricate system as specified by equipment manufacturer to combat rusting.

If two or more applications are planned in the same day, the sprayer can be kept clean by running water through the system between applications.


          Brushes/Rollers.

              1. Clean immediately after use.

              2. Wash thoroughly with bleach and water mix (1 part to 4 parts).


SAFETY FIRST

Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When working on steep or high areas. Take EXTREME CARE not to step on wet treated area. Surface may be slick until dry.

It is good practice to wear respirator or mask and protect hands with rubber gloves when spraying any coating or chemical. When engineered air control is not feasible, use properly maintained and properly fitted NIOSH approved respirator for solvent vapors. A dusk mask does not provide protection against vapors.

If eye contact occurs, flood with water for fifteen (15) minutes and call a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.

thatching thatch roof

HOME | CONTACT US | FIRE RETARDANT WOOD